CORIOLIS FLOW & DENSITY MEASUREMENT ENABLE SKID DESIGNS THAT RAISE PRODUCTION QUALITY BY 30 PERCENT
03 May 2005 - Emerson Process Management

Emerson Process Management has applied its Micro Motion Coriolis technology to enable Euroelettra Sistemi SpA, a leader in the automation of ceramics production from Italy, to design a skid-mounted blending system for ceramic slip and coloring materials. Euroelettra customers have experienced up to 30 percent improvement in production quality by using the new skid systems that enable actual blending of batches of the ceramic raw materials to take place immediately at the time of use, compared to the traditional approach of mixing and maintaining mass quantities for use over extended periods.

Using the technology and measurement accuracy of the Micro Motion Coriolis flowmeter from Emerson, Euroelettra Sistemi can now consistently monitor and control both the density and flow rate of the components being blended. The technique is likely to revolutionize the production of colored ceramics, which previously had been based on craft rather than science.

The skid blending system produced by Euroelettra Sistemi has brought significant productivity and efficiency benefits when introduced into companies that had been using the traditional approach. In one of the first production installations at a manufacturer of floor and wall tiles, the benefits included:

Major savings in production space required, since mixing tanks are not required when the blending is done only at the time of use.

Electricity and water consumption is reduced due to elimination of the requirement for continuous agitation and significantly reduced cleaning.

Production repeatability and consistency have reached an unheard of level of 90%, compared to a maximum of 70% previously, this owing to the close control over the color mixing.

Conventional production of colored ceramics involved preparation and blending of the base suspension or slip, and the color, in quantities of tens of tons at a time. Repeated color analysis and color addition ensured that once the color had reached the desired level, enough material was available for a reasonable production quantity to be modeled and fired, achieving a consistent result.

Typically the blending occurred in ball mills, and then in underground agitation tanks, which required significant amounts of energy to maintain the agitation, over the days while the material was being used in the modeling process. Inevitably the large tanks and mills required a lot of cleaning, thereby wasting the material that was deposited on the tank walls and associated pipework. High quality products required dedicated tanks to avoid impurity carry-over from previous batches.

Euroelettra Sistemi realized that the most efficient mixing process would be a skid-based unit, and that this would require accurate monitoring and control of the separate materials being delivered. The barrier to achieving this was overcome once Euroelettra investigated the accuracy and measurement capabilities of the Micro Motion T-Series flowmeter from Emerson, which provides both mass flow and density measurements. This introduced the possibility of blending the color and the slip in exact mass proportions, achieving consistent color hue even though the actual blended volume is small.

The diagnostics available within the Multi-Variable Digital core processor of the flowmeter, accessible via a Modbus connection, enables the blending system to identify any build-up of material within the straight measuring tube of the Micro Motion Coriolis flowmeter. This ability to signal when cleaning is required has increased equipment availability by around 50%, and improves efficiency. Cleaning is relatively straightforward, when needed, because of the straight tube design of the flowmeter. The resulting homogeneity of the material supplied has led to a reduction of typical production rejects by over 90% compared to previous skid blending system trials.

Future benefits will follow. Traceability of the process parameters used to achieve each blend enables further production batches to be scheduled as needed, with good color consistency between batches, which both improves productivity and increases customer satisfaction. Several manual production operations have been eliminated, releasing the people for other work. The production efficiency has been increased by 50%, impacting the whole company, enabling an overall increase of 10% in efficiency.

The Euroelettra mission is the creation of automation systems and the management of production processes with a high technological content. The know-how acquired over the years, continued study of the most innovative control and management techniques, and the use of leading-edge materials, make Euroelettra Sistemi a reliable partner for the chemical, metallurgical, food, glass and agro-food industries. Relying on us means fully achieving the goal of optimization of resources and improvement of production processes.

http://www.emersonprocess.com

More News:
  • For May 2005
  • From Emerson Process Management
  • For Sensors and Sensor Technology